Electric Scooter Kit 10'' Hub Motor Brushless Toothless Scooter Hub Motor Wheel

48V/52V/60V Electric Scooter LCD Display Accelerator Use Electric Scooters. Ebike Controller 36V48V52V60V Electric Bike Display LCD Display For Electric.

10 inch Electric Scooter Motor Wheel Shock Absorption Fork Modified Front Wheel. 2pcs Alloy Motorcycle Brake Handle Brake Lever MTB Cylinder Lever Black. Wuxing Electric Bike Thumb Throttle mtb Handle Waterproof Thumb Throttle Bicycle. Bicycle Lights Ebike LED Front Bike Light Headlight Bicicle 12V-80V Waterproof. 9-90v Double 1A 2A USB Charger Universal Electric Scooter Motorcycle USB E-bike.

Electric Bicycle 36V48V24V 250W 500W 1000W Electric Bike Controller LCD display. 36V48V 40A 1000W Double Drive Electric Bicycle Scooter Dual Drive Controller Kit. Controller and LCD display Kit For 10 inch 36V 350W500W 48V 500W800W1000W. Note: for this one motor, the 10 inch size is the motor with tyre size. Not the tyre, only this one hub is not 10 inch. Hope you can check the size before you order it. Power: 350W, 500W, 600W, 800W, 1000W. 2 Set Tire(include the inner tube). Red wire (D+): power supply positive input.

Black wire (GND): negative pole of power supply. Blue line (DS): Controller electric door lock. Green wire (RX): communication reception.

White line (TX): communication transmission. Speed display, battery indicator, fault indicator, headlight indicator, cruise indicator, gear indicator, total mileage, single mileage. Real-time voltage, running current, running time, start mode. P01: Backlight brightness, level 1 is the darkest, level 3 is the brightest.

P02: Mileage unit, 0: KM; 1: MILE. P03: Voltage level: 24V, 36V, 48V, default 36V. P04: Sleep time: 0, no sleep; other numbers are sleep time, range: 1-60; unit minute. P05: Power-assisted drive gear setting.

P06: Wheel diameter: unit, inch; precision: 0.1. P07: Number of speed magnets: range: 1-100. P08: Speed limit, the maximum operating speed of the motor. P09: Zero start, non-zero start setting, 0: zero start; 1: non-zero start.

P10: Drive mode setting 0 Power-assisted drive 1 Electric drive 2 Power-assisted drive Electric drive coexistence. P11: Assist sensitivity setting 1-24. P12: Starting torque: range: 0-5, 0 is the weakest, 5 is the strongest.

P13: Magnet type setting of booster plate 5 8 12. P14: Controller current limit value setting Default 12A range: 1-20A; (requires controller software support). P15: Motor drive signal percentage setting (to achieve the speed limit function of PO8) full speed is set to 100. P16: Instrument real-time cruise function 1 With this function 0 Without this function. P17: Headlight synchronization function 1 Headlights and backlight do not light up after turning on 0 Headlights and backlight light up after turning on.

P18: Power-on password selection function 1 With this function 0 Without this function. P99: One-key recovery function in the P99 parameter setting interface, press and hold the MODE key for 5-6 seconds, and all parameters will be restored to the first.

Initial settings for the second boot. ODO: ODO clear in the ODO parameter setting interface, first short press the MODE button and then long press for 5M-6 seconds until the number is zero, release. The specific status of the fault content is as follows. ERRO 4: Power-off brake lever.

ERRO 6: Communication failure, the meter cannot receive the output of the controller. ERRO 7: Communication failure, the controller cannot receive the output of the instrument.